Carbon Aeronautics quadcopter
Robot / hardware buildTeensy 4.0 quadcopter taught step by step in a 222-page build and programming manual, with a PCB upper frame and separate per-chapter Arduino code repositories; manual and code are licensed CC BY-NC-SA 4.0. [3] [4] [7]
Build & first use →Official websiteUpstream build guide
- For
- Adults (manual states 18+) with previous electronics and programming experience [3]
- Cost
- No current cost or bill of materials established yet.
- Source rights
- Named licenses are documented by part. Includes noncommercial terms. Review licenses
- Unknowns
- operating system not fully established. Review gaps
Source researched · Not tested by us
Sources checked · Research details
Licenses & related hardware
- Ecosystem
- Arduino
- License
- CC BY-NC-SA 4.0 (noncommercial) · Details by part
Overview
The Carbon Aeronautics quadcopter is taught through a build and programming manual, first edition August 2022, by Laurens Raes. Readers start with breadboard projects and work up to rate, angle and vertical-velocity flight controllers on a Teensy 4.0. The manual calls itself an educational product, not a toy, intended for adults with previous electronics and programming experience. It suits learners who want to write the flight code themselves rather than configure existing firmware. [1] [3]
Is this for you?
- Use cases
- Education in flight control, sensors and embedded programming
Derived from stated manual purpose.
- Known limitations
- Manual and code are noncommercial (CC BY-NC-SA 4.0)
- Frame PCB design files on OSHWLab were not preserved or inspected
- 10-minute flight time is a calculated hover upper limit, not a measured figure
- No upstream price or BOM total identified
Source-review boundaries; no build or flight performed.
What you need
- Host computer
A computer capable of running Arduino
- Dependencies
- Arduino IDE with Teensyduino
Manual setup page names Arduino software together with Teensyduino.
- Tools
- Soldering iron or station and solder
- Soldering helping hand
- Wire stripper and cutter
- Computer capable of running Arduino
- Hex keys 1.5 mm and 2 mm
- Multimeter
- Skills
- Soldering
- Arduino programming
- Use of a multimeter
Hardware & parts
- Actuators
- Four GEPRC GR1105 5000 kV motors with HobbyKing 6A ESCs (with BEC) and Gemfan 3018 propellers
Manual also describes tested GR1206 4500 kV / 12A ESC and alternative propeller options.
- Controller
Teensy 4.0 microcontroller programmed as the flight controller
- Sensors
- GY-521 MPU-6050 orientation sensor
- GY-BMP280 barometer
- Power
Turnigy 2S 1300 mAh Li-Po (1000 and 1500 mAh 2S also tested), HobbyKing B3AC charger
- Dimensions
Maximum propeller diameter 10.2 cm (4 inch); battery bay 12 x 4 x 3 cm with practical space 8.5 x 3.3 x 1.5 cm
Assembly & first use
Open the upstream getting-started guide [3]
- Read the safety and regulation statements
- Obtain the listed parts, PCB frames, tools and a computer for Arduino/Teensyduino
- Work through the breadboard projects (LEDs, battery voltage, gyroscope, motors, receiver) before assembly
- Assemble the lower and upper PCB frames (Project 10)
- Load the rate, angle or vertical-velocity flight controller code from the chapter repositories
Editorial source-navigation sequence, not a reproduced or safety-qualified procedure.
Cost
No current, complete configuration-specific build cost has been established for this profile.
Rights, cost and gaps
The manual's text and figures are licensed CC BY-NC-SA 4.0, and the headers of the Part XVI angle-mode and Part XX vertical-velocity code apply the same terms. That permits noncommercial adaptation with attribution and share-alike. It does not grant commercial-use rights, and no separate license file was identified in the repositories. GitHub reported no license for the manual repository. [2] [3] [7] [8]
No upstream price, BOM total or kit price was identified, so no budget is given. No assembly, flashing or flight was performed for this profile. [4]
3D preview
Preview not available yet. The reviewed sources did not establish a supported 3D payload for a hosted preview. The design may be supplied as drawings, an external CAD document or a separate download.
Model sources
The reviewed sources did not establish a supported 3D payload for a hosted preview. The design may be supplied as drawings, an external CAD document or a separate download.
Project notes
What the base build uses
Project 1 lists a Teensy 4.0, a GY-521 MPU-6050 orientation sensor, a GY-BMP280 barometer, four GEPRC GR1105 5000 kV motors with HobbyKing 6A ESCs, Gemfan 3018 propellers, a Turnigy 2S 1300 mAh battery with a HobbyKing B3AC charger, and a Flysky FS-i6 transmitter with an FS-iA6B receiver. The lower and upper frames are Carbon Aeronautics parts. The manual gives the basic build's weight as 247 g. It reports tested alternatives, including 1000 or 1500 mAh 2S batteries and a GR1206 4500 kV motor with a 12A ESC, and says the heaviest combination weighs 278 g. Propellers are limited to 10.2 cm diameter. Required tools include a soldering iron, wire stripper and cutter, 1.5 and 2 mm hex keys, a multimeter and a computer that runs the Arduino software with the Teensyduino add-on. [4]
The upper frame is a printed circuit board that carries the control electronics, power distribution and most of the wiring. The Part 0 README says the frame PCB was designed in EasyEDA and links it on OSHWLab. Those design files were not preserved or inspected for this profile, so their completeness and license are unknown. [5] [6]
Claims to read carefully
The cover lists a 10-minute flight time. In the simulation chapter that figure is calculated from hover current with a 1300 mAh battery and described as an upper limit, with real flights expected to be shorter. The worked numbers also shift from 7.4 A to 7.8 A within the calculation. Treat it as an estimate, not a measured endurance. [3] [5]
The safety page tells builders never to charge batteries unattended and to check their country's rules on altitude, speed and weight before flying outdoors. Its motor guidance needs care: one line says to remove the propellers until the program is known to work, and the next says never to run motors without propellers. The page does not reconcile the two, so the intended test sequence should be confirmed in the relevant project chapter or with the author. The manual makes the user responsible for complying with local unmanned-aircraft regulations. [3] [4]
What we checked
Source research only; no installation, physical build, flashing or flight test performed. No affiliate links added.
Not yet established
- Requirements: operating system
Updates
- Upstream last updated
- Apr 22, 2023 [2]
- Latest release
- Not established
- Profile updated
- Oct 5, 2026
- Sources last checked
- Oct 5, 2026
- Next review
- Nov 5, 2026
- Reviewed revision
- Manual repository commit 2082da709ba92cba52f63452bff8eaa844be60c9 (snapshot, no release; manual first edition August 2022); code: Part XVI 8b15fcc98a14, Part XX 138f8bf324a8 · repository
Source files and licenses
Manual and flight code are public under CC BY-NC-SA 4.0 (noncommercial); frame PCB files on OSHWLab were not preserved, so hardware rights and completeness remain unresolved.
| Layer | Availability / license |
|---|---|
| mechanical design | not found · License not fully assessed Lower and upper frames are PCBs whose EasyEDA design is linked on OSHWLab; the page returned HTTP 403 to preservation, so files and their license were not inspected. No frame files in the GitHub repositories reviewed. [1] [6] |
| electronics | not found · License not fully assessed Manual describes the PCB upper frame and wiring schematic; editable PCB design is on OSHWLab and was not preserved or inspected. Its license was not established. [5] [6] |
| firmware | available · CC BY-NC-SA 4.0 Chapter repositories contain single ArduinoCode files whose headers apply CC BY-NC-SA 4.0 (noncommercial). No separate license file identified in the inspected repositories. [7] [8] |
| documentation | available · CC BY-NC-SA 4.0 Manual text and figures licensed CC BY-NC-SA 4.0 per the rights page (noncommercial). No license file in the repository. [3] |
Flight code runs on the Teensy and is assessed as firmware; no separate host software identified.
Flight control does not use learned weights.
No dataset is part of the build.
References
Each source links to the exact revision we read. “Used for” shows where this page relies on it.
- S001 Manual repository README
Manual purpose, video series and link to frame design files on OSHWLab.Revision, date & where cited
Carbon Aeronautics (Laurens Raes) · github.com · revision
2082da7· README.md at · Accessed Oct 5, 2026
Used for: Overview, Is this for you?, Source files and licenses - S002 Manual repository revision metadata
Selected commit, dates, popularity signals and absence of a GitHub license hint.Revision, date & where cited
Carbon Aeronautics (Laurens Raes) · github.com · revision
2082da7· ; commit snapshot, no published release · Accessed Oct 5, 2026
Used for: Cost, What we checked - S003 Quadcopter build and programming manual: cover and rights page
Cover claims, CC BY-NC-SA 4.0 statement for text and figures, liability, age and local-regulation statements.Revision, date & where cited
Carbon Aeronautics (Laurens Raes) · github.com · revision
2082da7· Carbon_Aeronautics_Quadcopter_Manual.pdf, PDF pages 1 and 4 (First edition, August 2022) · Accessed Oct 5, 2026
Used for: Overview, Is this for you?, Assembly & first use, Cost and 2 more - S004 Manual Project 1: parts, alternatives, tools and safety
Base parts list, tested alternatives, weights, required tools, general safety instructions and Teensy/Arduino setup start.Revision, date & where cited
Carbon Aeronautics (Laurens Raes) · github.com · revision
2082da7· Carbon_Aeronautics_Quadcopter_Manual.pdf, PDF pages 10, 13-18 · Accessed Oct 5, 2026
Used for: What you need, Hardware & parts, Assembly & first use, Cost and 2 more - S005 Manual Projects 10 and 21: PCB frame and flight-time estimate
Upper frame is a PCB carrying power and signal traces; 10-minute flight time is a calculated hover upper limit.Revision, date & where cited
Carbon Aeronautics (Laurens Raes) · github.com · revision
2082da7· Carbon_Aeronautics_Quadcopter_Manual.pdf, PDF pages 81 and 192 · Accessed Oct 5, 2026
Used for: Is this for you?, Hardware & parts, Assembly & first use, What the base build uses and 2 more - S006 Part 0 repository README (frame PCB design)
Frame PCB designed in EasyEDA; design linked on OSHWLab.Revision, date & where cited
Carbon Aeronautics (Laurens Raes) · github.com · revision
c350b03· README.md at · Accessed Oct 5, 2026
Used for: Is this for you?, What the base build uses, Source files and licenses - S007 Part XVI angle-mode flight controller code
Code header applies CC BY-NC-SA 4.0 terms and disclaims liability.Revision, date & where cited
Carbon Aeronautics (Laurens Raes) · github.com · revision
8b15fcc· ArduinoCode header at · Accessed Oct 5, 2026
Used for: Is this for you?, Assembly & first use, Cost, Source files and licenses - S008 Part XX vertical-velocity flight controller code
Code header applies CC BY-NC-SA 4.0 terms and disclaims liability.Revision, date & where cited
Carbon Aeronautics (Laurens Raes) · github.com · revision
138f8bf· ArduinoCode header at · Accessed Oct 5, 2026
Used for: Assembly & first use, Cost, Source files and licenses
Correction guidance · Discussion is not enabled · Profile format 0.7.0-draft.5
Change history
2026-10-05 — Initial intake from manual repository snapshot and chapter code repositories (Growbotics comparison lead verified against upstream).