Open Source RoboticsRobots, software & learning

F1TENTH / RoboRacer

Robot / hardware build

Ackermann-steered racing research platform; the preserved Xavier NX/Slash guide differs from its newer Orin Nano Super/Fiesta parts list and requires configuration-specific calibration. [1]

Build & first use →Official websiteBill of materials

For
Robotics labs comfortable with RC hardware, Jetson setup and ROS configuration [1]
Cost
No current cost yet. Upstream bill of materials [9]
Source rights
Some licenses are unresolved. Includes noncommercial terms. Review licenses
Unknowns
tools not fully established. Review gaps

Source researched · Not tested by us
Sources checked · Research details

Upstream paper photograph of an F1TENTH course vehicle with Jetson Xavier NX, extracted from Figure 3. This is the older course configuration, not the newer Orin Nano Super/Fiesta parts list.
Upstream paper photograph of an F1TENTH course vehicle with Jetson Xavier NX, extracted from Figure 3. This is the older course configuration, not the newer Orin Nano Super/Fiesta parts list. Johannes Betz, Hongrui Zheng, Felix Jahncke, Zirui Zang, Florian Sauerbeck, Y. Rosa Zheng, Joydeep Biswas, Venkat Krovi and Rahul Mangharam · CC-BY-4.0. Embedded image extracted from page 5 of the source PDF and losslessly decoded to PNG; no retouching.
Licenses & related hardware
License
MIT, CC-BY-NC-SA-4.0 (noncommercial) · license not fully assessed for mechanical design, electronics · Details by part

Requirements · Research details and dates

On this page

Overview

The preserved documentation uses the RoboRacer name for this F1TENTH-linked RC racing platform. Its build page selects a Traxxas Slash 4x4 chassis and Jetson Xavier NX, while the linked workbook now includes a newer Fiesta ST Rally VXL and Orin Nano Super configuration. These are different build generations. This entry records the pinned guide and the newer workbook without claiming that their instructions form one validated configuration. [1] [5] [9]

Is this for you?

Known limitations
  • Pinned guide and live workbook describe different chassis/compute generations
  • Deck3.1 folder contains V3 filenames despite changed file sizes
  • External deck rights and complete matched firmware configuration unresolved

Source comparison, not a fit or operation test.

[5] [9] [10] [11] · Editorial assessment

3D preview

F1TENTH official RViz proxy. The official F1TENTH Gym ROS RViz proxy: a source-sized chassis box, four wheels and laser cylinder at zero steering positions. It is a simplified simulation visualization, not detailed chassis CAD, a manufacturing model or verification of a selected physical build.

The 3D preview loads after the page.

Drag to orbit · Scroll or pinch to zoom · Right-drag to pan. Use the view buttons for front, side and top views. The tree shows names supplied by the source; unnamed bodies remain labeled as such.

Download original URDF source bundle (ZIP) · File checksums and provenance

Separate bodies can be inspected in the model tree. Explode is a viewing aid, not an assembly sequence.

Source, license and scale

Source: F1TENTH contributors / Hongrui Zheng, revision 883394df0964c555ee05bea69c3002daf6f2d405. Original and preview: MIT. Preview conversion by Open Source Robotics; source files unchanged inside the downloadable bundle. Preview coordinates are centered and rounded to six decimal places. URDF visual origins, mesh scales and joint transforms applied at zero joint positions, then metres converted to millimetres. No physical part tested.

Viewer: three-cad-viewer 5.0.7 (MIT license). Confirm scale and manufacturing settings before printing.

What you need

Operating system
  • Pinned native guide: Ubuntu20.04/ROS2Foxy on Xavier-or-newer hardware with JetPack5-era setup

Guide scope; not validation of current Orin hardware or current supported OS.

[6]

Host computer

Onboard Jetson plus pit/host computer or monitor, keyboard and mouse for setup.

[6]

Hardware & parts

Upstream bill of materials [9]

Hardware configuration

RC-based Ackermann-steered racing platform; pinned guide selects Traxxas Slash4x4 and Jetson XavierNX.

[5]

Controller

Jetson ROS driver stack and VESC motor/steering interface; newer workbook lists OrinNanoSuper and VESC6MkVI.

[6] [9] [12]

Sensors
  • Hokuyo10LX lidar in both inspected parts-list generations

[9]

Assembly & first use

Project documentation [1]

Assembly

Purchased RC chassis, laser-cut platform deck, compute, lidar, power board and VESC; deck/power-board revisions must match.

[5] [9] [10] [11]

Calibration

Tune steering offset/gain and motor ERPM-to-speed conversion for actual wheelbase and drivetrain after manual control works.

[8]

Cost

No current, complete configuration-specific build cost has been established for this profile.

Project notes

Choose a complete hardware generation before ordering

The workbook section dated May 15, 2026 lists Orin Nano Super, Hokuyo 10LX, a power board and VESC 6 MkVI, with an estimated total of 3022.29. Optional equipment and separate tools/peripheral sections complicate that total; this review did not verify a current delivered quote. Older workbook sections retain Xavier NX and TX2-era choices. Do not copy a price from one section and assembly assumptions from another. [9]

The linked deck folder contains V3 files and a V3.1 folder labeled for a new power board. Files inside the latter still use V3 names, with different sizes from the older files. A filename alone therefore does not establish the deck revision. The listings were preserved, but the geometry, fit and linked-file licenses were not verified. [10] [11]

The pinned driver guide is a Foxy-era setup

The native driver instructions describe ROS 2 Foxy on Ubuntu 20.04 with Xavier-or-newer Jetson hardware and JetPack 5-era setup. They direct older configurations to a separate Docker route. This is the scope of the saved guide, not evidence that the same image and commands reproduce the newer Orin configuration. [6]

The separately preserved f1tenth_system stack provides launch files and parameters and depends on VESC, Ackermann command multiplexing and teleoperation packages. Its README and submodule file name different VESC branches; exact dependency commits were preserved to avoid relying on those moving branch names. No stack compilation or device connection was performed. [12] [14] [15]

Calibrate the actual car before autonomy experiments

VESC setup varies with controller hardware and tool generation. The guide distinguishes servo-output configuration methods, including older non-default firmware. A firmware recipe for an older controller is not established as compatible with every newer VESC in the workbook. [7] [9]

After manual control works, upstream calibrates motor direction, steering center and gain, and the conversion between motor electrical RPM and vehicle speed. Initial checks use a supported car with its wheels free; later distance and turning measurements depend on the actual wheelbase and drivetrain. Record those measurements and configuration values before using odometry for mapping or localization. The guide’s example turn diameter is not a universal target for every chassis. [8]

The driver README also distinguishes the Logitech F710 deadman controls for manual driving and navigation. Confirm the selected joystick mapping rather than assuming those buttons apply unchanged to the newer workbook’s controller. [9] [12]

The documentation carries CC-BY-NC-SA-4.0 terms; the separately inspected driver-stack root uses MIT. Neither establishes blanket rights for linked CAD, purchased components or all dependencies. This is a source-based platform profile with explicit version gaps, not a tested racing build or performance result. [3] [13]

What we checked

Source research only; no installation, physical build or performance test performed. No affiliate links added.

Not yet established

  • Requirements: tools
  • A step-by-step setup summary

Updates

Upstream last updated
Jan 9, 2026 [2]
Latest release
Aug 16, 2023 [2]
Profile updated
Oct 26, 2026
Sources last checked
Oct 1, 2026
Next review
Oct 31, 2026
Reviewed revision
94efb99a2df0fdf29954501f02c8de6c50ae20f9 (release foxy) · combined hardware and software repository

Source files and licenses

Available project sources support research coverage; complete build and commercial qualification remain separate.

LayerAvailability / license
mechanical designavailable · License not fully assessed
CAD filenames and revisions listed; raw geometry, complete chassis source and explicit linked-file license not verified. [10] [11]
electronicsavailable · License not fully assessed
Build integration instructions and parts evidence; matched complete board manufacturing source and rights not established. [5] [9]
firmwarenot found · License not fully assessed
Guide describes VESC firmware choices, but complete matched firmware source for the selected hardware build not established here; ROS driver source is separate. [7] [15]
softwareavailable · MIT
Driver-stack root license; dependencies preserved separately and retain their own terms. [12] [13] [15]
documentationavailable · CC-BY-NC-SA-4.0
Noncommercial documentation license; not blanket licensing for linked CAD, software or purchased hardware. [1] [3]

Selected physical and driver-stack profile does not select a learned model or dataset.

References

Each source links to the exact revision we read. “Used for” shows where this page relies on it.

Correction guidance · Discussion is not enabled · Profile format 0.6.0-draft.1

Change history

2026-10-26 — Added attributed upstream media with linked reuse terms; technical evidence dates unchanged.