Open Source RoboticsRobots, software & learning

InMoov

Robot / hardware build

A modular printable humanoid with body-section tutorials, tendon-driven hands and a separate MyRobotLab control route. [1] [2] [3] [5]

Build & first use →Official websiteUpstream build guide

For
Makers interested in incremental humanoid construction; Educational builders with fabrication support [1]
Cost
No current cost or bill of materials established yet.
Source rights
Some licenses are unresolved. Includes noncommercial terms. Review licenses
Unknowns
host computer, operating system not fully established. Review gaps

Source researched · Not tested by us
Sources checked · Research details

Photograph of an InMoov head and upper torso at Maker Faire Berlin, May 26, 2018; a historical build, not a complete assembled humanoid.
Photograph of an InMoov head and upper torso at Maker Faire Berlin, May 26, 2018; a historical build, not a complete assembled humanoid. Matti Blume · CC-BY-SA-4.0. Original image unchanged; displayed responsively. Preview re-encoded for faster display; the link opens the original file.
Licenses & related hardware
License
CC-BY-NC-3.0 (noncommercial) · license not fully assessed for documentation · Details by part

Requirements · Research details and dates

On this page

Overview

InMoov is organized as a modular humanoid build, with separate finger, hand, arm, head and torso instructions. That makes a small mechanism a useful starting point, but it also means the STL library is not one ready-to-order robot configuration. Our local collection preserves 413 linked STL files across 36 categories, including different generations and optional parts. Each file has a checksum; the collection is a dated download snapshot, not a single upstream release or a verified complete build. [1] [5]

Is this for you?

Known limitations
  • The STL library mixes body sections, generations, alternatives and derivatives
  • Hand i2 component list is not a full humanoid bill of materials
  • Servo power and controls must be matched to the chosen section; no complete robot setup tested

[1] [2] [3] [5]

What you need

Dependencies
  • Arduino controller route described by build overview
  • MyRobotLab and Python scripts for the documented control route

[1] [2] [3] [5]

Tools
  • 3D printer and slicer with fit calibration
  • Drills and M3 tap for i2 hand post-processing
  • Soldering tools for i2 finger sensors
  • Fastening and small-part fitting tools

[1] [2] [3] [5]

Hardware & parts

Hardware configuration

Modular humanoid; reviewed starting configurations are Finger Starter and one i2 hand

[1] [2] [3] [5]

Actuators
  • Finger Starter: one appropriately sized servo
  • One i2 hand BOM: six JX-6225MG 300-degree servos

[1] [2] [3] [5]

Assembly & first use

Open the upstream getting-started guide [1] [2] [3] [5] · Project documentation [1] [2] [3] [5]

Assembly

Print the fit calibrator, select a consistent body-section design, post-process parts and install tendons, servos and wiring.

[1] [2] [3] [5]

Calibration

Tutorials specify printer fit calibration and servo centering; full robot calibration not reproduced.

[1] [2] [3] [5]

Cost

No current, complete configuration-specific build cost has been established for this profile.

3D preview

Preview not available yet. The reviewed design license includes a noncommercial restriction. The original design is linked; a hosted derivative needs a separate reuse decision.

Project notes

A finger test and an i2 hand have different scopes

The Finger Starter tutorial uses four named printed parts, one servo and an Arduino Uno. It asks builders to print a fit calibrator before the full part set and to clear hinge holes after printing. It also warns that servo current can reset the Arduino and recommends an appropriate external supply. A successful finger build would test one mechanism and its power arrangement, not qualify a full humanoid. [2]

The i2 hand is a larger task. Its one-right-hand list specifies six JX-6225MG 300-degree servos, springs, braided line, PTFE guides, five AH3503 Hall sensors and magnets. The assembly includes drilling, tapping, fitting finger joints, routing tendons and soldering sensor wires. Printer access alone therefore does not describe the tools or labor required. [3]

The i2 instructions also refer to forearm and wrist-interface parts during assembly. Reconcile those adjoining modules with the selected hand before ordering or printing; the hand list should not be treated as the BOM for an entire arm. Keep the calibration sample, file versions, servo choice and cable route with that selected configuration. [3]

Separate the printed files from the control system

The main guide describes an Arduino and MyRobotLab/Python route. The Finger Starter page distinguishes scripts for different MyRobotLab generations. We preserved selected tutorials and the STL collection, but did not establish a complete matched software, electronics and firmware pack or reproduce the control setup. [1] [2] [5]

The STL library identifies Gaël Langevin's design under CC BY-NC 3.0. That noncommercial declaration matters when considering a kit or fabricated-parts offer. Current component quotations, rights for the intended offer, and measured assembly, calibration and support work remain unresolved. [4]

What we checked

Source research only; no installation, physical build or performance test performed. No affiliate links added.

Not yet established

  • Requirements: operating system, host computer
  • A step-by-step setup summary

Updates

Upstream last updated
Not established
Latest release
Not established
Profile updated
Oct 26, 2026
Sources last checked
Sep 30, 2026
Next review
Oct 30, 2026
Reviewed revision
2026-09-30 website and per-file checksum snapshot

Source files and licenses

Available project sources support research coverage; complete build and commercial qualification remain separate.

LayerAvailability / license
mechanical designavailable · CC-BY-NC-3.0
Library declaration credits Gaël Langevin; noncommercial terms do not establish permission for commercial kits. [4] [5]
electronicsnot found · License not fully assessed
Tutorials identify Arduino, sensors and MyRobotLab routes, but a complete matched source/software pack was not preserved in this STL and tutorial review. [1] [2] [3]
firmwarenot found · License not fully assessed
Tutorials identify Arduino, sensors and MyRobotLab routes, but a complete matched source/software pack was not preserved in this STL and tutorial review. [1] [2] [3]
softwarenot found · License not fully assessed
Tutorials identify Arduino, sensors and MyRobotLab routes, but a complete matched source/software pack was not preserved in this STL and tutorial review. [1] [2] [3]
documentationavailable · License not fully assessed
Selected tutorials preserved; complete hardware map, all modules and controls not reconciled. [1] [2] [3]

No learned model or dataset selected for the finger/hand build route.

References

Each source links to the exact revision we read. “Used for” shows where this page relies on it.

  • S001 InMoov build overview
    Revision, date & where cited

    Gaël Langevin / InMoov · inmoov.fr · Captured source d77e0bc8ac68cc7c2b4d8e2121874c7b0a3c736cc87c19d400bc971187c00c86 · Accessed Sep 30, 2026


    Used for: Overview, Is this for you?, What you need, Hardware & parts and 3 more
  • S002 Finger Starter assembly tutorial
    Revision, date & where cited

    Gaël Langevin / InMoov · inmoov.fr · Captured source dba1f37ec89b7abca1e872dd3689768242fc7a5bcf7cbee7d02aa53616884380 · Accessed Sep 30, 2026


    Used for: Is this for you?, What you need, Hardware & parts, Assembly & first use and 3 more
  • S003 Hand i2 assembly and component list
    Revision, date & where cited

    Gaël Langevin / InMoov · inmoov.fr · Captured source 26f0fa27ff40bbca868544f736631ab7026e78b104c7afa221aca3f2e2155721 · Accessed Sep 30, 2026


    Used for: Is this for you?, What you need, Hardware & parts, Assembly & first use and 2 more
  • S004 STL library and license declaration
    Revision, date & where cited

    Gaël Langevin / InMoov · inmoov.fr · Captured source 1dd00d7bf9269bdaec8baf5b0ca3aeb9ed772eafdc398cd195c662f3fc049b84 · Accessed Sep 30, 2026


    Used for: Separate the printed files from the control system, Source files and licenses
  • S005 Preserved STL file inventory
    Revision, date & where cited

    Gaël Langevin / project contributors · inmoov.fr · Local acquisition receipt for public STL URLs; individual SHA-256 values · Accessed Sep 30, 2026


    Used for: Overview, Is this for you?, What you need, Hardware & parts and 3 more
  • S006 Upstream image and reuse attribution
    Media-only review: Photograph of an InMoov head and upper torso at Maker Faire Berlin, May 26, 2018; a historical build, not a complete assembled humanoid. Reuse basis: CC-BY-SA-4.0. The photographer explicitly identifies InMoov at Maker Faire Berlin 2018. Visual review shows the modular printed head and partial torso with InMoov identification. Caption limits the pictured assembly and date; no claim it represents every current body section. Photographer rights declaration saved, not the Commons page-text license. Original image unchanged; displayed responsively. Technical/cost evidence dates unchanged.
    Revision, date & where cited

    Matti Blume · commons.wikimedia.org · File description, author, date, Licensing and original photograph; image SHA-256 037642d5d3b2c0631012f60b30d92c2f1822d874d5ccdb775d13aa6035f182bb · Accessed Oct 26, 2026

Correction guidance · Discussion is not enabled · Profile format 0.5.0-draft.1

Change history

2026-10-26 — Added attributed upstream media with linked reuse terms; technical evidence dates unchanged.