Linorobot
Robot / hardware buildConfigurable ROS 2 mobile-robot stack; this profile selects a two-wheel differential-drive, ESP32 control route with separately versioned firmware and measured chassis parameters. [1]
Build & first use →Official website
- For
- Builders able to select motors, wire electronics and configure ROS 2 [1]
- Cost
- No current cost or bill of materials established yet.
- Source rights
- Named licenses are documented by part. Review licenses
- Unknowns
- tools not fully established. Review gaps
Source researched · Not tested by us
Sources checked · Research details
Licenses & related hardware
- License
- Apache-2.0 · Details by part
Overview
Linorobot2 combines ROS 2 navigation, mapping and state estimation with a configurable mobile base. This profile selects the documented two-wheel differential-drive route with an ESP32 running micro-ROS. It is a configuration choice within a platform that also supports four-wheel skid-steer and mecanum robots, not a claim that a particular complete kit has been built or tested. [1] [5] [9]
Is this for you?
- Known limitations
- No single complete chassis BOM or delivered cost established for the selected route
- Humble firmware branch is unsupported; Teensy removed from Jazzy and Lyrical
- Simulation configuration does not replace physical odometry and sensor calibration
Configuration and documentation comparison, not a hardware test.
3D preview
Linorobot default 2WD simulation model. The default two-wheel-drive description uses simple source boxes, cylinders and spheres. This illustrates its configured chassis and sensor positions, not a detailed fabrication assembly or every Linorobot build.
The 3D preview loads after the page.
Drag to orbit · Scroll or pinch to zoom · Right-drag to pan. Use the view buttons for front, side and top views. The tree shows names supplied by the source; unnamed bodies remain labeled as such.
Download original URDF source bundle (ZIP) · File checksums and provenance
Separate bodies can be inspected in the model tree. Explode is a viewing aid, not an assembly sequence.
Model sources
The preview uses the linked original design. Source grouping is retained where present; the caption identifies whether this is an assembly or one component.
Source, license and scale
Source: Linorobot contributors, revision f6b0bd0350c4a9d6b815ef4bb5c701a1e5129711. Original and preview: Apache-2.0. Preview conversion by Open Source Robotics; source files unchanged inside the downloadable bundle. Preview coordinates are centered and rounded to six decimal places. URDF visual origins, mesh scales and joint transforms applied at zero joint positions, then metres converted to millimetres. No physical part tested.
Viewer: three-cad-viewer 5.0.7 (MIT license). Confirm scale and manufacturing settings before printing.
What you need
Hardware & parts
Assembly & first use
Cost
No current, complete configuration-specific build cost has been established for this profile.
Project notes
Preserve software and firmware as separate revisions
The ROS packages and microcontroller firmware live in different repositories. The main overview still mentions Teensy, but the separately preserved firmware guide says Teensy was removed from Jazzy and Lyrical, with its remaining Humble branch unsupported. The firmware guide lists Jazzy with Ubuntu 24.04 and Lyrical with Ubuntu 26.04. Match the ROS branch, firmware branch and board target rather than following an old Teensy recipe against a newer firmware checkout. [1] [9] [11]
For the selected ESP32 route, the firmware handles motor control and publishes encoder odometry and IMU data through micro-ROS. The ROS computer fuses those measurements and runs the higher-level stack. The installation guide requires robot software on the workstation used to build the firmware; the onboard-computer configuration also needs it on the robot. [5] [9]
A supported drive type is not a complete parts list
A two-wheel build still needs a chosen chassis, encoder-equipped motors, compatible drivers, power components and sensors. The reviewed documentation supplies reference wiring and configurable robot descriptions, but this review has not reconciled a complete procurement list or current delivered price for one manufactured chassis. Choose and record those parts before assigning a budget or copying geometry values. [4] [9]
The firmware distinguishes two-wheel differential drive, four-wheel skid-steer and mecanum kinematics. Its example motor, encoder and wheel constants are configuration inputs. They are not measurements of the robot on your bench. [9]
Establish reliable odometry before mapping
Upstream calibration instructions require the robot to be elevated with its wheels clear of the ground. Check motor direction and encoder sign, then establish counts per revolution, wheel diameter and wheel separation for the actual assembly. The guide also explains limiting commanded speed below the motor maximum so the speed controller retains room to correct errors. [9]
An IMU requires its own orientation and configuration checks; the firmware guide explicitly allows initial testing without one and warns that a misconfigured IMU can break navigation. Verify the base measurements and transforms before interpreting a distorted map as a planner problem. This sequence is an editorial synthesis of the calibration and ROS setup documentation, not a reproduction result. [7] [8] [9]
The main repository and separately preserved firmware carry Apache-2.0 licenses. Their robot-description templates and reference diagrams do not establish complete manufacturing source for every purchased motor, driver or sensor. No firmware compilation, installation, hardware calibration or navigation run was performed in this review. [3] [10]
What we checked
Source research only; no installation, physical build or performance test performed. No affiliate links added.
Not yet established
- Requirements: tools
- A step-by-step setup summary
Updates
- Upstream last updated
- Sep 29, 2026 [2]
- Latest release
- Not established
- Profile updated
- Oct 1, 2026
- Sources last checked
- Oct 1, 2026
- Next review
- Oct 31, 2026
- Reviewed revision
- f6b0bd0350c4a9d6b815ef4bb5c701a1e5129711 (commit snapshot; no published stable release found) · combined hardware and software repository
Source files and licenses
Available project sources support research coverage; complete build and commercial qualification remain separate.
| Layer | Availability / license |
|---|---|
| mechanical design | available · Apache-2.0 Software, documentation and robot-description templates; mechanical description is not a complete manufacturing design for the selected chassis. [3] [4] |
| electronics | available · Apache-2.0 Reference wiring and configuration documentation, not manufacturer source for every purchased board. [9] [10] |
| firmware | available · Apache-2.0 Separate preserved firmware; no build or compatibility test performed. [9] [10] [11] |
| software | available · Apache-2.0 Software, documentation and robot-description templates; mechanical description is not a complete manufacturing design for the selected chassis. [3] [4] |
| documentation | available · Apache-2.0 Software, documentation and robot-description templates; mechanical description is not a complete manufacturing design for the selected chassis. [3] [4] |
Selected mapping/navigation platform uses no selected learned policy or training dataset.
References
Each source links to the exact revision we read. “Used for” shows where this page relies on it.
- S001 linorobot/linorobot2: README.md
Revision, date & where cited
github.com · revision
f6b0bd0· Accessed Oct 1, 2026
Used for: Overview, Is this for you?, What you need, Hardware & parts and 2 more - S002 linorobot/linorobot2: commit f6b0bd0
- S003 linorobot/linorobot2: LICENSE
Revision, date & where cited
github.com · revision
f6b0bd0· Accessed Oct 1, 2026
Used for: Establish reliable odometry before mapping, Source files and licenses - S004 linorobot/linorobot2: files
Revision, date & where cited
github.com · revision
f6b0bd0· archive file inventory · Accessed Oct 1, 2026
Used for: A supported drive type is not a complete parts list, Source files and licenses - S005 Linorobot software: docs/installation.md
Revision, date & where cited
github.com · revision
f6b0bd0· Accessed Oct 1, 2026
Used for: Overview, What you need, Hardware & parts, Preserve software and firmware as separate revisions - S006 Linorobot software: docs/base_controller.md
Revision, date & where cited
github.com · revision
f6b0bd0· Accessed Oct 1, 2026 - S007 Linorobot software: docs/odometry.md
Revision, date & where cited
github.com · revision
f6b0bd0· Accessed Oct 1, 2026
Used for: Establish reliable odometry before mapping - S008 Linorobot software: docs/transforms.md
Revision, date & where cited
github.com · revision
f6b0bd0· Accessed Oct 1, 2026
Used for: Establish reliable odometry before mapping - S009 Separate firmware: README.md
Revision, date & where cited
github.com · revision
1ed605a· Accessed Oct 1, 2026
Used for: Overview, Is this for you?, What you need, Hardware & parts and 5 more - S010 Separate firmware: LICENSE
Revision, date & where cited
github.com · revision
1ed605a· Accessed Oct 1, 2026
Used for: Establish reliable odometry before mapping, Source files and licenses - S011 Preserved firmware inventory
Revision, date & where cited
github.com · revision
1ed605a· Separate firmware snapshot, not an installed matched system · Accessed Oct 1, 2026
Used for: Preserve software and firmware as separate revisions, Source files and licenses
Correction guidance · Discussion is not enabled · Profile format 0.6.0-draft.1