Open-source Leader Arm
Teleoperation inputUnpowered 3D-printed six-joint leader arm read by AS5600 encoders through an ESP32, used to teleoperate an SO-ARM follower in MuJoCo or through LeRobot. [1]
Build & first use →Official websiteUpstream build guideBill of materials
- For
- SO-ARM100/101 and LeRobot users comfortable with hand-wiring I2C modules, flashing an ESP32 and running Python plugins [1]
- Cost
- INR 2,619.00 upstream parts estimate [1] · checked Oct 5, 2026 · DetailsNot included: 3D-printed parts and filament, follower arm, its controller and power supply and host computer and more.
- Source rights
- Named licenses are documented by part. Review licenses
Source researched · Not tested by us
Sources checked · Research details
Licenses & related hardware
- License
- Apache-2.0 · Details by part
Overview
This project replaces the servo-driven LeRobot leader arm with an unpowered, 3D-printed arm whose six joints are read by AS5600 magnetic encoders. An ESP32 streams the joint angles to a host, which drives a follower. It is an input device: it has no actuators of its own and needs a separate SO-ARM follower, physical or simulated. This entry is source research only; nothing was printed, flashed or run. [1]
Is this for you?
- Use cases
- Teleoperating a simulated SO-ARM100 in MuJoCo
- Teleoperating a physical so101_follower through LeRobot
- Recording LeRobot datasets in simulation or with a physical follower
- Known limitations
- README states testing against a simulated SO-ARM; no physical-follower test report in inspected sources
- Default home angles, ranges and directions are fixed in configuration
- Plugins depend on unpinned lerobot
- No follower arm included
Source-review boundaries; no hardware tests.
More on fit and limitations
Who it suits
It suits SO-ARM100/101 users who want a cheaper, lighter leader and can wire I2C modules by hand. The README says the arm is currently tested against a simulated SO-ARM in MuJoCo and also gives LeRobot commands for a physical so101_follower. The inspected sources do not include a test report for a physical follower; the README links an independent build write-up that was not reviewed here. [1]
What you need
- Operating system
- Windows (COM ports in examples)
- Linux and macOS (/dev/ttyUSB0 noted)
- Host computer
A PC running Python 3.10 or newer; the README notes integrated graphics limit simulated recording to about 30 fps.
No minimum specification stated beyond the Python requirement and the frame-rate note.
- Dependencies
- lerobot (unpinned)
- pyserial
- mujoco, numpy and pynput for the simulated follower plugin
- MuJoCo Menagerie trs_so_arm100 model for simulation
- Arduino IDE with ESP32 board support
- Skills
- Hand wiring and soldering on perfboard
- FDM printing with a mid-print pause
- Arduino IDE flashing
- Python and LeRobot command-line use
Inferred from the documented build and software steps.
[1] · Editorial assessment
Hardware & parts
Upstream bill of materials [1]
- Hardware configuration
Passive six-joint leader arm with encoder-instrumented joints and a handle; no actuators.
- Sensors
- 6× AS5600 magnetic rotary encoders with diametric magnets
- Power
Powered from the ESP32 USB connection; encoders and multiplexer run from the 3V3 rail per the wiring table.
No separate power supply is listed in the BOM.
[1] · Editorial assessment
Assembly & first use
Open the upstream getting-started guide [1]
- Buy encoders with magnets, bearings, multiplexer, ESP32, wire and screws
- Print 49 parts, pausing bearing_housing prints at 10 mm to insert bearings
- Wire encoders through the TCA9548A and assemble joints 0 to 5
- Flash firmware.ino with Arduino IDE and check the boot magnet diagnosis
- Install the LeRobot plugins (or standalone scripts) and align the leader to the follower rest pose
- Assembly
25-step README guide using step images; encoders for joints 0 and 5 attach early and the other four last; rubber band spans two housings.
Cost
| Version | Price |
|---|---|
| Leader arm electronics and hardware, commit 3cf2ee4 README BOM | INR 2619.00 [1] Parts estimate |
India (upstream INR prices) · Checked 2026-10-05
| Included | 6× AS5600 encoder with diametric magnet; 6× 608 bearing; TCA9548A multiplexer; ESP32; 28 AWG silicone wire; 60 M3×10 screws; Perfboard |
|---|---|
| Not included | 3D-printed parts and filament; Follower arm, its controller and power supply; Host computer; Shipping, taxes and assembly labor |
| Stock | Supplier stock not rechecked. |
| Delivery and tax | Not established. |
Price details
Maintainer-published INR component total with the README's own conversion of about US$27.45; not re-quoted.
India (upstream INR prices) · Checked 2026-10-05 · Quantity 1
Printed parts, an SO-ARM follower (physical or simulated) and a host PC.
Cost scope
The README lists 2,619 INR (about US$27.45) for encoders, bearings, multiplexer, ESP32, wire, screws and perfboard, excluding printed parts. These are the maintainer's Indian prices with their own conversion, not re-quoted. The follower arm, its controller and power supply, the host computer and filament are excluded. The README's comparison of six servos at about $24 each is the author's estimate, not a sourced SO-101 price. [1]
3D preview
Preview not available yet. Design-source links are available. A configuration-matched assembly and its file-level reuse scope have not yet been reviewed for a hosted preview.
Model sources
Design-source links are available. A configuration-matched assembly and its file-level reuse scope have not yet been reviewed for a hosted preview.
Project notes
Configuration to reconcile
- Electronics: six AS5600 encoders with diametric magnets, a TCA9548A I2C multiplexer (the AS5600 has a fixed 0x36 address), an ESP32, 608 bearings, 28 AWG wire and a perfboard. The wiring tables put the multiplexer on ESP32 pins 18 and 19 and give each joint its own channel. [1] [4]
- Printing: 19 unique and 49 total parts in PLA at 0.2 mm layers and 15% infill, without supports. Each bearing_housing needs a mid-print pause at 10 mm to insert a bearing. STL, STEP and a Bambu Lab A1 3MF are in the repository. [1] [5]
- Firmware: firmware.ino uses only the Arduino Wire library, prints a per-channel magnet diagnosis at boot, then streams six comma-separated raw readings at 100 Hz over 115200-baud serial, with -1 for an unreadable channel. [1] [4]
- Software: two Python plugins register an encoder_leader teleoperator and a MuJoCo SO-ARM100 robot for LeRobot; standalone scripts drive MuJoCo without LeRobot. Both plugin packages are version 0.1.0, need Python 3.10 or newer and depend on an unpinned lerobot. Simulation also needs the trs_so_arm100 model from MuJoCo Menagerie. [1] [6]
Calibration is a single alignment: hold the leader in its reference pose while the follower is at rest, then press Enter. The plugin's default home angles, joint ranges and directions are fixed values in config_encoder_leader.py, so a different follower build may need them adjusted; that was not tested. [1] [7]
What we checked
Source research only; no printing, flashing, installation or teleoperation performed. No affiliate links. AI-assisted drafting with a separate LLM editorial judge; no independent human technical review.
Updates
- Upstream last updated
- Sep 15, 2026 [2]
- Latest release
- Not established
- Profile updated
- Oct 5, 2026
- Sources last checked
- Oct 5, 2026
- Next review
- Nov 5, 2026
- Reviewed revision
- 3cf2ee41e645afe1173dda79914ffe31e174d7a6 (commit snapshot; no published release found) · combined hardware and software repository
Source files and licenses
CAD, wiring documentation, firmware and plugins are in one repository under a root Apache-2.0 license file; the follower and purchased modules are outside scope.
| Layer | Availability / license |
|---|---|
| mechanical design | available · Apache-2.0 STEP, STL, 3MF and GLB files under cad_files; root Apache-2.0 is the only license file identified, with no hardware-specific license. [3] [5] |
| electronics | available · Apache-2.0 Wiring diagram and pin tables for off-the-shelf modules on perfboard; no PCB design. Purchased modules keep their own terms. [1] [3] |
| firmware | available · Apache-2.0 Single Arduino sketch using the built-in Wire library; ESP32 board-support and toolchain terms are separate. [3] [4] |
| software | available · Apache-2.0 Two LeRobot plugins and standalone MuJoCo scripts; lerobot, MuJoCo and Menagerie model terms are separate. [3] [6] |
| documentation | available · Apache-2.0 README with BOM, wiring, print settings and assembly images. [1] [3] |
Teleoperation input device; no trained models distributed.
No dataset distributed; users record their own.
Licenses and gaps
A single Apache-2.0 LICENSE sits at the repository root; no separate hardware, firmware or documentation license or NOTICE file was identified. Purchased modules and the MuJoCo Menagerie model keep their own terms. [3] [5]
No published release was identified at retrieval (the releases API returned none); this entry covers commit 3cf2ee4 from September 15, 2026, which had 129 GitHub stars at retrieval, a dated popularity signal only. Gripper handling, joint-limit fit with a physical SO-101, encoder accuracy and latency remain unverified. [2]
References
Each source links to the exact revision we read. “Used for” shows where this page relies on it.
- S001 Open-source Leader Arm README
Purpose, test status, BOM, wiring, print settings, firmware, LeRobot and standalone software use, assembly steps.Revision, date & where cited
github.com · revision
3cf2ee4· README.md at · Accessed Oct 5, 2026
Used for: Overview, Is this for you?, What you need, Hardware & parts and 4 more - S002 Matheshwaranpitchai/open-source-leader-arm: commit 3cf2ee4
No published release; default-branch commit snapshot archived; dated repository popularity.Revision, date & where cited
github.com · ; commit date 2026-09-15T19:25:21Z; manifest retrieved 2026-10-05 · Accessed Oct 5, 2026
Used for: What we checked, Source files and licenses - S003 Matheshwaranpitchai/open-source-leader-arm: LICENSE
Root Apache-2.0 license file; only license file identified.Revision, date & where cited
github.com · revision
3cf2ee4· LICENSE (Apache License 2.0 text) · Accessed Oct 5, 2026
Used for: Source files and licenses - S004 ESP32 encoder firmware
I2C multiplexer and AS5600 read loop, boot diagnosis and 100 Hz serial stream.Revision, date & where cited
github.com · revision
3cf2ee4· Accessed Oct 5, 2026
Used for: Hardware & parts, Configuration to reconcile, Source files and licenses - S005 Pinned archive file inventory
CAD (STEP, STL, 3MF, GLB), docs images, firmware and two LeRobot plugin packages; one license file.Revision, date & where cited
github.com · revision
3cf2ee4· Complete filename inventory of archive (78 members); not a printability test · Accessed Oct 5, 2026
Used for: What you need, Configuration to reconcile, Source files and licenses - S006 LeRobot plugin package metadata
Package names, versions, Python requirement and unpinned lerobot dependency.Revision, date & where cited
github.com · revision
3cf2ee4· lerobot_teleoperator_encoder_leader/pyproject.toml and lerobot_robot_mujoco_so_arm/pyproject.toml · Accessed Oct 5, 2026
Used for: Is this for you?, What you need, Configuration to reconcile, Source files and licenses - S007 Encoder leader default configuration
Joint names, default home angles, directions, joint ranges, port and baud rate.Revision, date & where cited
github.com · revision
3cf2ee4· Accessed Oct 5, 2026
Used for: Is this for you?, Hardware & parts, Assembly & first use, Configuration to reconcile
Correction guidance · Discussion is not enabled · Profile format 0.7.0-draft.5
Change history
2026-10-05 — Created from Growbotics-listing lead; all claims checked against preserved upstream sources. No physical build or test.