Open Source RoboticsRobots, software & learning

OpenCat robots

Robot / hardware build

Nybble/Bittle robot-family entry centered on OpenCat 1.2.5 NyBoard firmware, calibration and host tools; software openness does not establish complete frame or electronics manufacturing sources. [1]

Build & first use →Official website

For
Builders and educators using a matched Nybble/Bittle model and NyBoard revision [1]
Cost
No current cost or bill of materials established yet.
Source rights
Named licenses are documented by part. Review licenses
Unknowns
host computer, tools, operating system not fully established. Review gaps

Source researched · Not tested by us
Sources checked · Research details

Licenses & related hardware

Requirements · Research details and dates

On this page

Overview

OpenCat is the firmware and host-tool framework used by Petoi's Nybble and Bittle robots. This family entry reviews release 1.2.5's ATmega328P-based NyBoard path. It does not treat every Petoi board or later robot variant as compatible with the same sketch. The source describes Bittle with nine axes and Nybble with eleven, including eight leg axes for each; there is no single family-wide degree-of-freedom count. [1] [2] [5]

Is this for you?

Known limitations
  • README example and actual sketch select different NyBoard revisions
  • Board-specific serial settings differ in the header
  • Optional modules can disable gyro functionality to fit limited program memory
  • Main archive does not establish complete frame CAD, board manufacturing or a matched complete BOM
  • No firmware upload, calibration, hardware or performance tests performed

Source-inspection boundaries for release 1.2.5.

[1] [5] [6] [7] · Editorial assessment

3D preview

Petoi Bittle ROS robot description (ros_opencat). One robot of this family entry is shown: Bittle, the robot selected by the OpenCat setup example and firmware default. The Petoi ros_opencat repository at commit 8596292 supplies the Fusion 360-exported bittle.xacro (expanded without changes) and its STL meshes, shown at zero joint positions: 87 link meshes on the source joint tree with the 9 actuated joints (8 leg joints and the head). The separate Nybble description in the same repository is not shown. The model is a ROS simulation description; it does not state which Bittle hardware generation it represents, and it is not tied to the OpenCat 1.2.5 firmware release reviewed for this profile. Servo, battery, screw and Petoi logo shapes are part of the exported model; no trademark rights are implied. The repository is MIT-licensed, but its notice names the holder only as cc and Petoi gives no CAD-specific notice, so no manufacturing or redistribution clearance is claimed. Fit and motion are not verified.

Ambiguous license holder: the ros_opencat repository LICENSE is the MIT License with the copyright line “Copyright (c) 2022 cc”. The bittle_description folder carries the MIT notice of the fusion2urdf export tool (“Copyright (c) 2018 Toshinori Kitamura”), and its package.xml license field is an unfilled placeholder. Petoi gives no CAD-specific notice for these meshes. Open Source Robotics shows the model for reference with attribution to Petoi under its policy for ambiguous licenses. The Petoi logo shapes in the model are Petoi’s marks. No manufacturing, redistribution or trademark clearance is claimed. License: ros_opencat LICENSE (MIT, holder given as “cc”) · upstream notice.

The 3D preview loads after the page.

Drag to orbit · Scroll or pinch to zoom · Right-drag to pan. Use the view buttons for front, side and top views. The tree shows names supplied by the source; unnamed bodies remain labeled as such.

Download original URDF source bundle (ZIP, LZMA compression) · File checksums and provenance

Separate bodies can be inspected in the model tree. Explode is a viewing aid, not an assembly sequence.

Source, license and scale

Source: Petoi (PetoiCamp), revision 85962928970ee47f38d53cad56f8e304863a87f5. Original and preview: MIT (ros_opencat LICENSE, Copyright (c) 2022 cc); no CAD-specific notice from Petoi. Preview conversion by Open Source Robotics; source files unchanged inside the downloadable bundle. Preview coordinates are centered and rounded to six decimal places. URDF visual origins, mesh scales and joint transforms applied at zero joint positions, then metres converted to millimetres. No physical part tested.

Viewer: three-cad-viewer 5.0.7 (MIT license). Confirm scale and manufacturing settings before printing.

What you need

Dependencies
  • Arduino-compatible toolchain for the selected NyBoard
  • Robot-specific skill tables and board compile-time definitions
  • Optional host tools and sensor libraries have separate requirements

[1] [5] [6]

Hardware & parts

Hardware configuration

Robot family: Bittle dog and Nybble cat; selected release targets their ATmega328P NyBoard configurations.

[1] [5]

Actuators
  • Bittle: nine axes in source description, including eight leg axes and one head axis
  • Nybble: eleven axes in source description, including eight leg axes, two head axes and one tail axis

Configuration-specific counts; no single family-wide DOF or interchangeable-servo claim.

[1] [5]

Controller

ATmega328P-based NyBoard; pinned sketch defaults to NyBoard V1_2 while README example selects V1_0.

[1] [5]

Assembly & first use

Project documentation [1]

Calibration

Board-configuration mode initializes constants/skills and supports IMU calibration; joint offsets require a separate calibration step.

[1] [5]

Cost

No current, complete configuration-specific build cost has been established for this profile.

Project notes

Match the actual code to the hardware

The README's setup example selects Bittle and NyBoard V1_0, while the preserved OpenCat.ino actually defaults to Bittle and NyBoard V1_2. The header contains separate board definitions: V1 variants use 115200 baud, while V0_1 and V0_2 use 57600. Copying the README's serial setting without checking the selected board would miss that distinction. [1] [5] [6]

The documented setup has a board-configuration phase followed by the main sketch. IMU calibration and joint-offset calibration are distinct steps. The README says automatic initialization preserves joint offsets, but the pinned implementation disagrees: with AUTO_INIT enabled, src/skill.h removes the confirmation condition and writes the servoCalib array into calibration EEPROM. The IMU code likewise runs its calibration without the prompt in configuration mode. Treat the README’s preservation statement as inconsistent with this release’s code, and do not rely on it to retain existing offsets. No upload, calibration or robot motion was performed in this review. [1] [5] [8] [9]

The sketch also notes that optional sensor/behavior modes can disable gyro code to conserve program memory. Adding a module therefore has a functional tradeoff, not just a library-installation step. The selected robot, board, modules and skill tables need to be considered together. [5] [6]

Available software is not a complete hardware release

The archive includes firmware, module tests, skill libraries, Python API/serial tools and a desktop interface. It also contains two STL artifacts, but their paths identify a servo test arm and a UI tool; they do not establish a complete Nybble or Bittle frame. The README links external build and product resources, which remain separate from this preserved software release. A matched mechanical/electronics manufacturing package and complete BOM have not been established here. [1] [7]

The root repository and main sketch declare MIT, while the sketch directs readers to third-party module notices for included code. That software grant is not automatically extended to externally hosted frame designs, board designs or applications. Likewise, links to users' reinforcement-learning demonstrations do not establish bundled, verified learned weights in the reviewed firmware configuration. [1] [3] [5] [7]

This entry is useful for comparing the two documented NyBoard robot configurations and avoiding setup mismatches. Current full-kit cost, component substitutions and physical performance remain unverified rather than inferred from demonstrations or retail availability claims. [1] [5] [6]

What we checked

Source research only; no installation, physical build or performance test performed. No affiliate links added.

Not yet established

  • Requirements: operating system, host computer, tools
  • A step-by-step setup summary

Updates

Upstream last updated
Jun 23, 2025 [2]
Latest release
Jun 23, 2025 [2]
Profile updated
Oct 4, 2026
Sources last checked
Oct 1, 2026
Next review
Oct 31, 2026
Reviewed revision
54da7b70e5fdbf94019b0fea23162641ef7e9508 (release 1.2.5) · combined hardware and software repository

Source files and licenses

Available project sources support research coverage; complete build and commercial qualification remain separate.

LayerAvailability / license
mechanical designnot found · License not fully assessed
No complete selected robot-frame or board-manufacturing package established in this software archive. The two inventoried STL files are a servo test arm and UI tool, not a complete robot body; linked external hardware needs separate review. [1] [7]
electronicsnot found · License not fully assessed
No complete selected robot-frame or board-manufacturing package established in this software archive. The two inventoried STL files are a servo test arm and UI tool, not a complete robot body; linked external hardware needs separate review. [1] [7]
firmwareavailable · MIT
Root MIT and sketch MIT notice; included third-party modules retain their own notices. External applications and hardware designs are not covered by inference. [1] [3] [5] [7]
softwareavailable · MIT
Root MIT and sketch MIT notice; included third-party modules retain their own notices. External applications and hardware designs are not covered by inference. [1] [3] [5] [7]
documentationavailable · MIT
Root MIT and sketch MIT notice; included third-party modules retain their own notices. External applications and hardware designs are not covered by inference. [1] [3] [5] [7]

Selected firmware uses programmed skill tables; promotional links to separate learned-policy applications do not establish a bundled model/dataset.

References

Each source links to the exact revision we read. “Used for” shows where this page relies on it.

Project sources

Videos

Correction guidance · Discussion is not enabled · Profile format 0.6.0-draft.1

Change history

2026-10-04 — Added 4 YouTube reference(s) (S010, S011, S012, S013): official channel or videos linked from the pinned upstream sources. Existing claims, source-check dates and evidence are unchanged.