Open Source RoboticsRobots, software & learning

pib

Robot / hardware build

A printable humanoid whose #5 basic design replaces the #4 part set and uses Raspberry Pi 5 compute. [5] [6] [7] [8] [9] [10]

Build & first use →Official websiteSource codeUpstream build guide

For
Makers; Schools and university robotics groups [1]
Cost
No current cost or bill of materials established yet.
Source rights
Some licenses are unresolved. Review licenses
Unknowns
host computer, operating system not fully established. Review gaps

Source researched · Not tested by us
Sources checked · Research details

Licenses & related hardware
License
GPL-3.0, AGPL-3.0 · license not fully assessed for documentation · Details by part

Requirements · Research details and dates

On this page

Overview

pib's #5 basic design is a full replacement for the #4 part set. The V5.0.0 release notes explicitly say not to combine the two generations. We preserved the newer V5.0.1 STL release, whose specific correction is B47-Power_Holder: the previous holder did not fit the intended splitter and requires reprinting. This is a concrete reason to retain the release number with the printed parts. [5] [6]

Is this for you?

Known limitations
  • #4 and #5 part sets must not be mixed
  • V5.0.1 requires replacing the V5.0.0 B47 power holder
  • Release notes conflict on supply current; linked calibration page still labels itself pib#4
  • Exact complete nonprinted BOM, software dependency pins and current delivered cost unresolved

[5] [6] [7] [8] [9] [10]

3D preview

Face–neck clamp. One face–neck clamp from the preserved V5.0.1 STL release, not a complete head or humanoid. Physical fit and print settings are untested.

The 3D preview loads after the page.

Drag to orbit · Scroll or pinch to zoom · Right-drag to pan. Use the view buttons for front, side and top views. The tree shows names supplied by the source; unnamed bodies remain labeled as such.

Download original STL · File checksums and provenance

This model contains one geometric body.

Source, license and scale

Source: pib-rocks contributors, revision 7357d67513780d3eed3a9678a488b46572061626. Original and preview: GPL-3.0. Preview conversion by Open Source Robotics; original file unchanged. Preview coordinates are centered and rounded to six decimal places. STL does not declare units; confirm dimensions against the project design. No physical part tested.

Viewer: three-cad-viewer 5.0.7 (MIT license). Confirm scale and manufacturing settings before printing.

What you need

Dependencies
  • Separate pib-backend and Cerebra software
  • ROS2 and Tinkerforge dependencies installed by upstream setup route

[5] [6] [7] [8] [9] [10]

Tools
  • 3D printer and appropriate slicing configuration
  • microSD reader, keyboard, mouse and display with micro-HDMI adapter for setup

[5] [6] [7] [8] [9] [10]

Hardware & parts

Hardware configuration

Printable humanoid on a stand; this review scopes the #5 basic design

[5] [6] [7] [8] [9] [10]

Controller

Raspberry Pi 5 with 8 GB RAM and 64 GB SD card in #5 release notes

[5] [6] [7] [8] [9] [10]

Assembly & first use

Open the upstream getting-started guide [5] [6] [7] [8] [9] [10]

Assembly

Version-specific sequence: software and head, motor calibration and neck, hand/forearm, body, shoulder/elbow.

[5] [6] [7] [8] [9] [10]

Cost

No current, complete configuration-specific build cost has been established for this profile.

Project notes

Resolve two documentation mismatches before assembly

The #5 notes describe a Raspberry Pi 5 with 8 GB RAM, a 64 GB SD card, redesigned hands and changed arm servos. Their power specification is inconsistent: the overview table says 12 V, 20 A, while the detailed section says 12 V, 25 A. This profile does not choose between them. The exact supply, wiring and protection specification needs reconciliation with the selected #5 BOM. [6]

The current build index links a motor-calibration tutorial, but the captured tutorial still labels itself pib#4 and lists older motor references. It calls for calibration before installing motors. That is evidence of the assembly workflow, not verification that its exact settings apply to the changed #5 actuators. Resolve the generation mismatch before using those settings. [7] [9]

Nonprinted components are listed separately in Onshape and offered in vendor boxes. The build page distinguishes #5 basic, #4 Advanced and the forthcoming #5 Advanced. This review does not treat those variants as interchangeable or establish a current complete delivered price. [7]

Version the software as well as the prints

The setup tutorial requires a microSD reader, Pi power supply, keyboard, mouse and display connection, then directs builders to pib-backend. We preserved backend release v0.6.4 separately. Its README defaults to the pib5edu hardware variant and describes additional variant flags. However, its ordinary setup instructions download from main, and the backend and Cerebra branches also default to main. A repeatable build therefore needs both software revisions and their dependencies pinned alongside the STL release. [8] [10]

The STL archive carries GPL v3 text; the backend carries AGPL v3 text. These separate repository terms do not establish the rights or completeness of every CAD, firmware and purchased component. No installation, motor calibration or physical build was performed for this profile. [3] [10]

What we checked

Source research only; no installation, physical build or performance test performed. No affiliate links added.

Not yet established

  • Requirements: operating system, host computer
  • A step-by-step setup summary

Updates

Upstream last updated
Sep 8, 2026 [2]
Latest release
Sep 8, 2026 [2]
Profile updated
Oct 4, 2026
Sources last checked
Sep 30, 2026
Next review
Oct 30, 2026
Reviewed revision
7357d67513780d3eed3a9678a488b46572061626 (release V5.0.1) · combined hardware and software repository

Source files and licenses

Available project sources support research coverage; complete build and commercial qualification remain separate.

LayerAvailability / license
mechanical designavailable · GPL-3.0
STL repository license; does not resolve separately hosted CAD, purchased components or full system rights. [3] [4] [5]
electronicsnot found · License not fully assessed
Complete matched component manufacturing and firmware source set not established by these STL and backend archives. [4] [7] [10]
firmwarenot found · License not fully assessed
Complete matched component manufacturing and firmware source set not established by these STL and backend archives. [4] [7] [10]
softwareavailable · AGPL-3.0
Backend repository only; Cerebra and dependencies require their own revision and license preservation. [10]
model weightsnot found · License not fully assessed
No complete matched learned-model or training-data set preserved for this configuration. [4] [10]
datasetsnot found · License not fully assessed
No complete matched learned-model or training-data set preserved for this configuration. [4] [10]
documentationavailable · License not fully assessed
Separate public tutorials; calibration page has a generation mismatch requiring reconciliation. [7] [8] [9]

References

Each source links to the exact revision we read. “Used for” shows where this page relies on it.

Project sources

Videos

  • S011 pibrocks (YouTube channel)
    The project’s own YouTube channel, linked from the project’s own documentation. Not reviewed by us for accuracy.
    Revision, date & where cited

    YouTube channel pibrocks · youtube.com · Accessed Oct 4, 2026

  • S012 Meet pib – The Open Source Humanoid Robot for EVERYONE! (YouTube video)
    Video from the project’s own channel (pibrocks), linked from the project’s own documentation. Not reviewed by us for accuracy.
    Revision, date & where cited

    YouTube video pibrocks · youtube.com · Accessed Oct 4, 2026

Correction guidance · Discussion is not enabled · Profile format 0.5.0-draft.1

Change history

2026-10-04 — Added 2 YouTube reference(s) (S011, S012): official channel or videos linked from the pinned upstream sources. Existing claims, source-check dates and evidence are unchanged.