Raptor pellet extruder
End effectorA pellet-printing design for an Ender-3 conversion, with inventoried screw, barrel and heat-block geometry. [1] [2] [3]
Build & first use →Official website
- Cost
- No current cost or bill of materials established yet.
- Source rights
- Some licenses are unresolved. Review licenses
- Unknowns
- host computer, tools, operating system not fully established. Review gaps
Source researched · Not tested by us
Sources checked · Research details
Licenses & related hardware
- License
- MIT · license not fully assessed for documentation · Details by part
Is this for you?
- Known limitations
- Parts workbook includes machined screw/heat block and unpriced lab fasteners. It is not a fresh complete quote. Determine moving mass, heater control, flow calibration, pellet feed and orientation limits.
- No hardware build or test performed.
Source-researched; no physical verification.
Hardware & parts
Assembly & first use
Project documentation [1] [2] [3]
- Assembly
Parts workbook includes machined screw/heat block and unpriced lab fasteners. It is not a fresh complete quote. Determine moving mass, heater control, flow calibration, pellet feed and orientation limits.
Known prerequisites and unresolved assembly decisions; not a complete build instruction.
Cost
No current, complete configuration-specific build cost has been established for this profile.
3D preview
Preview not available yet. CAD files were identified. A configuration-matched assembly and its file-level reuse scope have not yet been verified for this preview.
Model sources
CAD files were identified. A configuration-matched assembly and its file-level reuse scope have not yet been verified for this preview.
Project notes
Mounting and application
Documented Ender-3 conversion. As an editorial adaptation assessment, robot-arm use would require evaluating mounting and motion/extrusion synchronization. The inspected evidence establishes no robot-arm interface. [1] [2] [3]
Before sourcing the build
The preserved Parts List/Complete Parts List.xlsx lists an extrusion screw and heat block, plus bolts with unpriced cost cells. Confirm manufacturing requirements and a complete purchasing list; the workbook does not establish a current delivered budget. [4] Determine moving mass, heater control, flow calibration, pellet feed and orientation limits. [1] [2] [3]
Files and reuse terms
The root license is MIT. It does not establish source availability or reuse rights for every separately sourced control or purchased component. Complete matched electronics, firmware and software source sets remain unestablished, without implying that such files are absent. [1] [2] [3]
The pinned inventory lists SolidWorks assemblies and parts, STL files and a DXF bracket, including screw, barrel and heat-block geometry. These are adaptation starting points, not fabrication-validated parts. They do not establish a complete, matched mechanical and control package. Current delivered cost and measured performance are not established; no hardware was built or tested for this profile.
What we checked
Source research only. No hardware assembly, performance testing, procurement or support qualification performed.
Not yet established
- Requirements: operating system, host computer, tools
- A step-by-step setup summary
Updates
- Upstream last updated
- Not established
- Latest release
- Not established
- Profile updated
- Oct 4, 2026
- Sources last checked
- Sep 30, 2026
- Next review
- Oct 30, 2026
- Reviewed revision
e56dc21
Source files and licenses
MIT root license. Parts workbook includes machined screw/heat block and unpriced lab fasteners. It is not a fresh complete quote. Determine moving mass, heater control, flow calibration, pellet feed and orientation limits.
| Layer | Availability / license |
|---|---|
| mechanical design | available · MIT MIT root license. Availability refers to the scoped files described here, not a complete configuration-matched manufacturing pack. [1] [2] [3] |
| electronics | not found · License not fully assessed A complete revision-matched source set for this tooling configuration was not established in the inspected documents. Standalone controls and purchased components require separate review; this is not a claim that no code or electronic files exist. [1] [2] [3] |
| firmware | not found · License not fully assessed A complete revision-matched source set for this tooling configuration was not established in the inspected documents. Standalone controls and purchased components require separate review; this is not a claim that no code or electronic files exist. [1] [2] [3] |
| software | not found · License not fully assessed A complete revision-matched source set for this tooling configuration was not established in the inspected documents. Standalone controls and purchased components require separate review; this is not a claim that no code or electronic files exist. [1] [2] [3] |
| documentation | available · License not fully assessed MIT root license. Availability refers to the scoped files described here, not a complete configuration-matched manufacturing pack. [1] [2] [3] |
This profile scopes hardware tooling, without selecting a learned controller or training dataset.
References
Each source links to the exact revision we read. “Used for” shows where this page relies on it.
Project sources
- S001 Raptor pellet extruder pinned tree
Revision, date & where cited
github.com · revision
e56dc21· Accessed Sep 30, 2026
Used for: Is this for you?, Hardware & parts, Assembly & first use, Mounting and application and 3 more - S002 Raptor pellet extruder / LICENSE
Revision, date & where cited
VidetteMakes · raw.githubusercontent.com · Accessed Sep 30, 2026
Used for: Is this for you?, Hardware & parts, Assembly & first use, Mounting and application and 3 more - S003 Raptor pellet extruder / README.md
Revision, date & where cited
VidetteMakes · raw.githubusercontent.com · Accessed Sep 30, 2026
Used for: Is this for you?, Hardware & parts, Assembly & first use, Mounting and application and 3 more - S004 Complete Parts List workbook
Lists screw and heat block quantities and several unpriced bolt rows; not a complete current quote.Revision, date & where cited
github.com · revision
e56dc21· ; Sheet1 rows 5, 7, 14–16 · Accessed Sep 30, 2026
Used for: Before sourcing the build
Videos
- S005 Vidette Makes (YouTube channel)
The project’s own YouTube channel, found by searching YouTube and checked against the channel page. Not reviewed by us for accuracy.Revision, date & where cited
YouTube channel Vidette Makes · youtube.com · Accessed Oct 4, 2026
Correction guidance · Discussion is not enabled · Profile format 0.6.0-draft.1
Change history
2026-09-30 — Classified in the end-effector hierarchy with cited mechanism and platform evidence; build and rights limitations retained.
2026-10-04 — Added 1 YouTube reference(s) (S005): official channel or videos linked from the pinned upstream sources. Existing claims, source-check dates and evidence are unchanged.