Open Source RoboticsRobots, software & learning

Solo

Robot / hardware build

A modular torque-controlled quadruped family; this review distinguishes wired Solo12 from its battery-and-wireless upgrade. [1]

Build & first use →Official websiteBill of materials

For
Legged robotics laboratories; Builders with precision assembly and embedded-control experience [1]
Source rights
Named licenses are documented by part. Review licenses
Unknowns
operating system not fully established. Review gaps

Source researched · Not tested by us
Sources checked · Research details

Upstream photograph of a Solo twelve-degree-of-freedom quadruped configuration.
Upstream photograph of a Solo twelve-degree-of-freedom quadruped configuration. Open Dynamic Robot Initiative, New York University and Max Planck Gesellschaft · BSD-3-Clause. Original image unchanged; displayed responsively.
Licenses & related hardware

Requirements · Research details and dates

On this page

Overview

The shared Open Dynamic Robot Initiative hardware archive contains Solo8, Solo12 and other robots. This profile focuses on the documented Solo12 configuration: four three-axis legs, a Master Board and six Micro Driver boards. Its v1 design receives power and Ethernet through a connection wire. The separately documented v1.1 upgrade adds batteries and wireless operation; those capabilities should not be assumed for a wired v1 build. [1] [5] [10]

Is this for you?

Known limitations
  • Hardware repository contains several designs; its popularity is not per-robot adoption
  • Exact full robot control software and all toolchain dependencies not reproduced
  • Current component stock and delivered complete configuration price unverified

[5] [6] [7] [8] [9] [11] [13]

3D preview

Solo12 body structure — back. One body-structure component from the Solo12 v1 design. This is not a complete robot or the Solo8 configuration. Upstream lists this STL under 3D Printed Parts; printing and scale have not been validated by us.

The 3D preview loads after the page.

Drag to orbit · Scroll or pinch to zoom · Right-drag to pan. Use the view buttons for front, side and top views. The tree shows names supplied by the source; unnamed bodies remain labeled as such.

Download original STL · File checksums and provenance

This model contains one geometric body.

Source, license and scale

Source: Max Planck Gesellschaft and New York University, revision 66af1522b4fba0ec4a1d7790e66f5e4652208d30. Original and preview: BSD-3-Clause. Preview conversion by Open Source Robotics; original file unchanged. Preview coordinates are centered and rounded to six decimal places. STL does not declare units; confirm dimensions against the project design. No physical part tested.

Viewer: three-cad-viewer 5.0.7 (MIT license). Confirm scale and manufacturing settings before printing.

What you need

Host computer

External real-time control computer; master-board SDK requires a direct Ethernet interface or compatible raw-wireless interface

[5] [6] [7] [8] [9] [11] [13]

Tools
  • Precision drills, reamers, metric taps and Helicoil installation tools
  • Mechanical assembly and soldering tools
  • Separate Micro Driver and Master Board flashing adapters
  • Printed joint-calibration fixtures

[5] [6] [7] [8] [9] [11] [13]

Hardware & parts

Upstream bill of materials [5] [6] [7] [8] [9] [11] [13]

Hardware configuration

Solo12 wired quadruped, with separately documented autonomy upgrade

[5] [6] [7] [8] [9] [11] [13]

Actuators
  • Modular brushless actuator cores with dual-stage belt transmission

[5] [6] [7] [8] [9] [11] [13]

Controller

Master Board v2 with six Micro Driver v2 boards in the documented BOM

[5] [6] [7] [8] [9] [11] [13]

Degrees of freedom

12

[5] [6] [7] [8] [9] [11] [13]

Assembly & first use

Project documentation [5] [6] [7] [8] [9] [11] [13]

Assembly

Prepare precision actuator cores and printed shells, assemble selected leg/body modules, wire custom electronics, then calibrate.

[5] [6] [7] [8] [9] [11] [13]

Calibration

Measure per-joint index-to-zero offsets with printed fixtures; roughly align legs at startup; repeat offset measurement after actuator repair or replacement.

[5] [6] [7] [8] [9] [11] [13]

Cost

No current, complete configuration-specific build cost has been established for this profile.

Project notes

The upgrade changes more than the power source

The v1.1 notes add two battery packs, revised body components, switches, an LED ring and a custom power-management board. They explicitly caution against using the LiPo packs without that board. We preserved the separate power-board repository, but its README still leaves the command-packet section unimplemented and the sensor-packet section unfinished. That is a documentation and integration gap, not a tested judgment about every function in its code. [10] [14]

The original robot itself requires precision actuator preparation. The v1.1 actuator-core option replaces several machining and shaft-preparation steps with a supplier encoder kit; the documentation describes it as functionally interchangeable with the earlier prepared shaft assembly. Current kit availability and total delivered cost remain unverified. Drilling, tapping, thread inserts, wiring and assembly still need their own tools and labor. [7] [8]

Calibration returns after repairs

Joint angles are initially unknown at power-on. The documented routine begins with rough manual alignment, finds encoder index positions and applies saved offsets. Printed calibration fixtures establish those offsets, and the documentation requires measuring them again if an actuator is repaired, replaced or modified. Include the fixtures and calibration procedure in a maintenance plan. [6]

We also preserved Master Board release v1.0.7. Its SDK requires a dedicated direct Ethernet interface; its wireless route needs monitor mode and packet injection. Its flashing guide has an explicit legacy ESP-IDF compatibility constraint. These requirements make the control computer and programming tools part of the build, alongside the printed robot. [11] [12] [13]

The hardware archive uses BSD-3-Clause terms; the separate Master Board and Power Board repositories use BSD-2-Clause. A complete matched controller stack, component quotations, assembly and support workload remain unverified. No hardware or firmware was operated for this profile. [3] [11] [14]

What we checked

Source research only; no installation, physical build or performance test performed. No affiliate links added.

Not yet established

  • Requirements: operating system
  • A step-by-step setup summary

Updates

Upstream last updated
Sep 6, 2022 [2]
Latest release
Not established
Profile updated
Oct 25, 2026
Sources last checked
Sep 30, 2026
Next review
Oct 30, 2026
Reviewed revision
66af1522b4fba0ec4a1d7790e66f5e4652208d30 (commit snapshot; no published stable release found) · combined hardware and software repository

Source files and licenses

Available project sources support research coverage; complete build and commercial qualification remain separate.

LayerAvailability / license
mechanical designavailable · BSD-3-Clause
Hardware repository scope; separately hosted boards and purchased components retain their own terms. [3] [5] [9]
electronicsavailable · BSD-3-Clause
Hardware repository scope; separately hosted boards and purchased components retain their own terms. [3] [5] [9]
firmwareavailable · BSD-2-Clause
Master Board repository only; not a complete robot control/dependency pack. [11] [12] [13]
softwareavailable · BSD-2-Clause
Master Board repository only; not a complete robot control/dependency pack. [11] [12] [13]
documentationavailable · BSD-3-Clause
Hardware repository scope; separately hosted boards and purchased components retain their own terms. [3] [5] [9]

No particular learned controller or dataset selected in this hardware review.

References

Each source links to the exact revision we read. “Used for” shows where this page relies on it.

Project sources

Videos

  • S015 Open Dynamic Robot Initiative (YouTube channel)
    The project’s own YouTube channel, linked from the project’s own documentation. Not reviewed by us for accuracy.
    Revision, date & where cited

    YouTube channel Open Dynamic Robot Initiative · youtube.com · Accessed Oct 4, 2026

  • S016 Integration test: 3DM-CX5-25 IMU + Motor control - Closed loop via Ethernet (YouTube video)
    Video from the project’s own channel (Open Dynamic Robot Initiative), linked from the project’s own documentation. Not reviewed by us for accuracy.
    Revision, date & where cited

    YouTube video Open Dynamic Robot Initiative · youtube.com · Accessed Oct 4, 2026

  • S017 Master board first wireless tests (YouTube video)
    Video from the project’s own channel (Open Dynamic Robot Initiative), linked from the project’s own documentation. Not reviewed by us for accuracy.
    Revision, date & where cited

    YouTube video Open Dynamic Robot Initiative · youtube.com · Accessed Oct 4, 2026

  • S018 20180914 Optical Foot Contact Switch Demonstration (YouTube video)
    Video from the project’s own channel (Open Dynamic Robot Initiative), linked from the project’s own documentation. Not reviewed by us for accuracy.
    Revision, date & where cited

    YouTube video Open Dynamic Robot Initiative · youtube.com · Accessed Oct 4, 2026

Correction guidance · Discussion is not enabled · Profile format 0.5.0-draft.1

Change history

2026-10-04 — Added 4 YouTube reference(s) (S015, S016, S017, S018): official channel or videos linked from the pinned upstream sources. Existing claims, source-check dates and evidence are unchanged.

2026-10-25 — Added an attributed upstream image with linked reuse terms; technical evidence dates unchanged.